Vizio Speaker SB4020EB0 User Manual

VIZIO  
QUICK START GUIDE  
Model: SB4020E-B0  
 
WARNING  
DO NOT INGEST BATTERY,CHEMICAL BURN HAZARD  
The remote control supplied with this product contains a coin/button cell battery.If the coin/button cell battery.If the coin/button cell battery is swallowed,it can cause severe internal burns  
in just two (2) hours and can lead to death.  
Keep new and used batteries away from children.If the battery compartment does not close securely,stop using the product and keep it away from children.  
If you think batteries might have been swallowed or placed inside any part of the body,seek immediate medical attention.  
A warning that batteries (battery pack or batteries installed) shall not be exposed to excessive heat such as sunshine,re,or the like.  
 
PACKAGE CONTENTS  
SUB- MUTE SUB+  
SRS  
TVOL  
SRS  
TSHD  
High Definition Sound Bar  
Remote Control with Battery  
Power Adapter w/Cable  
Stereo RCA to 3.5mm  
Audio Cable  
Digital Optical  
Cable  
This Quick Start Guide  
Wall Mount Template  
Wall Mount Brackets  
 
CONTROLS & CONNECTIONS  
Connections are located here:  
Power Port  
Aux Input  
Optical Input  
(Stereo 3.5mm)  
Service Port  
For use only by service technician.  
Sub Out  
Aux Input  
(Stereo RCA)  
Optical Input located on side:  
 
Controls located here:  
Power Button  
Input Button  
Volume Up/Down Buttons  
Indicator LEDs  
 
FIRST-TIME SETUP  
BOTTOM OF SOUND BAR  
1
GOOD  
BETTER  
BEST  
3.5MM TO RCA  
CABLE  
DIGITAL OPTICAL  
CABLE  
3.5MM TO RCA  
CABLE  
CHOOSE ONE CABLE:  
GOOD  
BETTER  
BEST  
AND CONNECT IT TO YOUR TV*  
 
*Not all TVs have the audio outputs shown above.To connect the Sound Bar directly to your other devices (Blu-ray player, game system, etc) see your devices user manual.  
2
3
4
 
5
Sound Bar is centered  
When  
using  
the  
below the TV.  
remote,point it at the  
center of the Sound  
Bar. The sensor is  
located there.  
For the best surround sound experience, position the Sound Bar as shown.*  
The Sound Bar should be close to ear level.  
 
6
Gently pull the plastic tab from  
the back of the remote control.  
(The plastic tab can be thrown away)  
7
Power  
Turn your TV on, then press the Power button on  
the remote to turn the Sound Bar on.  
MUTE SUB+  
SUB-  
Press the Input button to cycle through the audio  
inputs. For example, if you connected your TV to  
Aux 1, set the Sound Bar to Aux 1.  
Setup is complete.  
SRS  
TVOL  
SRS  
TSHD  
Input  
 
USING THE REMOTE  
Power  
Press to turn on or off.  
Volume Up  
Press to increase volume.  
Mute  
Press to mute.  
SUB +  
MUTE SUB+  
SUB-  
Press to increase subwoofer volume.  
SUB -  
Press to decrease subwoofer volume.  
Volume Down  
Press to decrease volume.  
SRS TruVolume  
SRS TruSurround HD  
Press to enable/disable SRS  
TruSurround HD.  
Press to enable/disable SRS TruVolume.  
SRS  
TVOL  
SRS  
TSHD  
Input  
Press to change input source.  
When using the remote, point it at the center of the Sound Bar.The sensor is located there.  
If your remote stops responding,you  
may need to replace the battery.  
To replace the battery, insert a  
flat-head screwdriver into the slot  
as shown. Gently push down on the  
tab, then press and pull downward  
on the battery cover to open.  
 
INDICATOR LEDS  
Indicator LEDs located here:  
Indicator LEDs flash according  
to input selection:  
Optical - Input 3*  
AUX - Input 2  
AUX - Input 1  
 
*Rapid flash indicates incompatible source or file format. If there is no sound output, see Help & Troubleshooting page.  
Indicator LEDs located here:  
When the four center  
Indicator LEDs are brightly  
lit, the selected SRS mode is  
enabled.When the LEDs are  
not lit, SRS mode is disabled.  
 
WALL MOUNTING THE SOUND BAR  
Place the included wall mounting  
template against the wall under your  
TV. Mark the locations of the 4 bracket  
holes using a pencil.  
1
32.24’’/ 819mm  
2
Be sure your screws are attached  
to wood studs or drywall anchors  
(for drywall) or concrete anchors  
(for brick/concrete walls).  
Screws for attachment to the wall are not included.  
Choose the screw type and length appropriate  
to your homes construction. If in doubt, consult a  
professional installer.  
If you are unfamiliar with power tools or the layout of electrical  
wiring in the walls of your home, consult a professional installer.  
 
VIZIO RECOMMENDS  
The VIZIO Co-Star™ Stream Player merges live TV and streaming entertainment into one experience,  
turning any HDTV into the ultimate smart TV. Using the latest version of Google TV™, Co-Star decks out  
your existing HDTV with apps, full-screen Web browsing and the best in streaming entertainment.And  
with 1080p Full HD resolution, built-in Wi-Fi, and 3D-readiness,VIZIO Co-Star is the ultimate entertainment  
upgrade for any high-definition television.  
Download fromAWvwawi.lSaombalenuaalst.cowmw. Awll M.VanIZuaIOls S.ceaorcmh And Download.  
This Product Sold Separately  
HELP & TROUBLESHOOTING  
• Press the POWER button on the remote control or on the top of your Sound Bar.  
• Ensure the power cord is securely connected.  
• Ensure the light on the power adapter is glowing green.  
There is no  
power.  
• Plug a different device into the electrical outlet to verify that the outlet is working correctly.  
• Increase the volume. Press Volume Up on the remote control.  
• Press MUTE on the remote to ensure the Sound Bar is not muted.  
• Press INPUT on the remote to select a different input source.  
• If you are using the 3.5mm output from your TV, be sure that is connected to an audio  
output and not audio input. Some TVs use 3.5mm audio input for devices such as  
computers.  
There is no  
sound.  
Your TV may be set to variable audio output. Confirm that the audio output setting is set  
to FIXED or STANDARD, not VARIABLE. Consult your TVs user manual for more detailed  
information.  
• If you are using a SPDIF/Optical connection, make sure your TV is set to PCM audio output.  
• Ensure all cables and wires are securely connected.  
I hear buzzing or  
humming.  
• Connect a different source device (TV, Blu-ray player, etc) to see if the buzzing persists. If it  
does not, the problem may be with the original device.  
• Connect your device to a different input on the Sound Bar.  
I want to return  
my Sound Bar to  
factory settings.  
• Press and hold the INPUT and Vol - buttons on the Sound Bar for 3 seconds to return it to its  
factory default settings.  
 
ONE-YEAR LIMITED WARRANTY  
ON PARTS AND LABOR  
Covers units purchased as new in United States and Puerto Rico Only  
VIZIO provides a warranty to the original purchaser of a new Product against defects in materials and workmanship for a period of one year of non-commercial usage and ninety  
(90) days of commercial use. If a Product covered by this warranty is determined to be defective within the warranty period,VIZIO will either repair or replace the Product at its  
sole option and discretion.  
To obtain warranty service, contact VIZIO Technical Support via email: TechSupport@VIZIO.com or via phone at 877 MY VIZIO (877.698.4946) from 6:00AM to 9:00PM Monday  
VIZIO SERVICE CENTER. Proof of purchase in the form of a purchase receipt or copy thereof is required to show that a Product is within the warranty period.  
Parts and Labor  
There will be no charge for parts or labor during the warranty period.Replacement parts and Products may be new or recertified atVIZIOs option and sole discretion.Replacement  
parts and Products are warranted for the remaining portion of the original warranty or for ninety (90) days from warranty service or replacement, whichever is greater.  
Type of Service  
Defective Products must be sent to a VIZIO service center to obtain warranty service.VIZIO is not responsible for transportation costs to the service center,but VIZIO will cover return  
shipping to the customer. PRE-AUTHORIZATION IS REQUIRED BEFORE SENDING ANY PRODUCT TO A VIZIO SERVICE CENTER FOR WARRANTY SERVICE.  
Product returns to VIZIOs service centers must utilize either the original carton box and shipping material or packaging that affords an equal degree of protection.VIZIOTechnical  
Support will provide instructions for packing and shipping the covered Product to the VIZIO service center.  
Limitations and Exclusions  
VIZIOs one-year limited warranty only covers defects in materials and workmanship.This warranty does not cover,for example:cosmetic damage,normal wear and tear,improper  
operation, improper voltage supply or power surges, signal issues, damages from shipping, acts of God, any type of customer misuse, modifications or adjustments, as well as  
installation and set-up issues or any repairs attempted by anyone other than by a VIZIO authorized service center. Products with unreadable or removed serial numbers, or  
requiring routine maintenance are not covered.This one year limited warranty does not cover Products soldAS IS”,“FACTORY RECERTIFIED”, or by a non-authorized reseller.  
THERE ARE NO EXPRESS WARRANTIES OTHER THAN THOSE LISTED OR DESCRIBED ABOVE. ANY IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF MERCHANT-  
ABILITY AND FITNESS FOR A PARTICULAR PURPOSE, SHALL BE LIMITED IN DURATION TO THE PERIOD OF TIME SET FORTH ABOVE. VIZIO’S TOTAL LIABILITY FOR ANY AND ALL LOSSES  
AND DAMAGES RESULTING FROM ANY CAUSE WHATSOEVER INCLUDING VIZIO’S NEGLIGENCE, ALLEGED DAMAGE, OR DEFECTIVE GOODS, WHETHER SUCH DEFECTS ARE  
DISCOVERABLE OR LATENT, SHALL IN NO EVENT EXCEED THE PURCHASE PRICE OF THE PRODUCT. VIZIO SHALL NOT BE RESPONSIBLE FOR LOSS OF USE, LOSS OF INFORMATION OR  
DATA, COMMERCIAL LOSS, LOST REVENUE OR LOST PROFITS, OR OTHER INCIDENTAL OR CONSEQUENTIAL DAMAGES. SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN  
IMPLIED WARRANTY LASTS OR THE EXCLUSION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO YOU.THIS WARRANTY  
GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS, WHICH VARY FROM STATE TO STATE. THIS WARRANTY IS SUBJECT TO CHANGE WITHOUT NOTICE.  
SPECIFICATIONS  
Sound Bar: Two 2-3/4High-Efficiency  
Full-Range Transducers  
Frequency Response 90 Hz - 19.5 KHz  
(Sound Bar):  
Voltage: 110-240 VAC, 50-60 Hz  
Dimensions (Sound Bar): 40.72W x 3.28H x 2.50D  
Net Weight (Sound Bar): 5.7 lbs  
Inputs: 1 x 3.5mm Stereo Audio  
1 x RCA Stereo Audio Pair  
1 x Optical Digital  
Sound Pressure Level: 95 dB  
Compliances: UL, FCC, cUL, NRCAN  
 
LEGAL & COMPLIANCE  
FCC Class B Radio Interference Statement  
NOTE:This equipment has been tested and found to comply with the limits for a Class B digital device,pursuant to Part 15 of the FCC Rules.These limits are designed to provide  
reasonable protection against harmful interference in a residential installation.This equipment generates, uses and can radiate radio frequency energy, and if not installed  
and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a  
particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the  
user is encouraged to try to correct the interference by one or more of the following measures:  
1. Reorient or relocate the receiving antenna.  
2. Increase the separation between the equipment and receiver.  
3. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.  
4. Consult the dealer or an experienced radio/TV technician for help.  
This device complies with Part 15 of the FCC Rules.Operation is subject to the following two conditions: (1) this device may not cause harmful interference,and (2) this device  
must accept any interference received, including interference that may cause undesired operation.  
Notice:  
1. The changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment.  
2. Shielded interface cables and AC power cord, if any, must be used in order to comply with the emission limits.  
3. The manufacturer is not responsible for any radio or TV interference caused by unauthorized modification to this equipment. It is the responsibilities of the user to correct  
such interference.  
RF Exposure Information  
This device meets the governments requirements for exposure to radio waves.This device is designed and manufactured not to exceed the emission limits for exposure to  
radio frequency (RF) energy set by the Federal Communications Commission of the U.S. Government.This device complies with FCC radiation exposure limits set forth for an  
uncontrolled environment.  
IC Statement  
Operation is subject to the following two conditions:  
1. This device may not cause interference, and  
2. This device must accept any interference, including interference that may cause undesired  
operation of the device.  
SRS is a trademark of SRS Labs,Inc. SRS technologies  
are incorporated under license from SRS Labs, Inc.  
This Class B digital apparatus complies with Canadian ICES-003.  
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.  
IC Radiation Exposure Statement  
This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled  
environment. This equipment should be installed and operated with minimum distance 20cm  
between the radiator & your body.  
This product qualifies for ENERGY STAR in thefactory default”  
setting and this is the setting in which power savings will  
be achieved. Changing the factory default settings or  
enabling other features will increase power consumption  
that could exceed the limits necessary to qualify for ENERGY  
STAR rating.  
Disposal and Recycling  
You must dispose of this product properly, according to local laws and regulations. Because this  
product contains electronic components and a battery, it must be disposed of separately from  
household waste. Contact local authorities to learn about disposal and recycling options.  
 
DO YOU HAVE QUESTIONS?  
LET US HELP!  
YOUR PRODUCT INCLUDES FREE LIFETIME TECH SUPPORT  
The VIZIO support team is highly  
trained and is based in the  
United States.  
We can help with:  
• New Product Setup  
• Connecting Your Devices  
• Technical Problems  
• And More  
Phone: (877) 878-4946 (TOLL-FREE)  
Email: techsupport@VIZIO.com  
Hours of operation:  
Monday - Friday: 5 am TO  
Saturday - Sunday: 8 am TO  
9
pm (pST)  
pm (pST)  
4
 
We speak English • Se habla Español • Nous parlons Français  
© 2013 VIZIO INC.ALL RIGHTS RESERVED.  
130207OC-NC  
 

Tascam DVD Player DV D01U User Manual
TechniSat Satellite Radio ST 6002 S User Manual
Timex Watch WW W302 062 095000 User Manual
Tripp Lite Power Supply APS PV User Manual
Turtle Beach Headphones XP400 User Manual
Uniden Film Camera GC43 User Manual
Uniflame Indoor Fireplace EF700SP User Manual
VDO Dayton Car Stereo System CD 5526 X User Manual
VocoPro CD Player CDG 1020PRO User Manual
Vulcan Hart Convection Oven SG4C ML 114876 User Manual